Super 32″ – 42″ Pipe Bending Machine

DMI International Pipe Bending Machine 32-42

PRODUCT DETAILS

 

BORE (IN) STROKE (IN) ROD (IN)
InBoard Cylinder 10 5 3.5
OutBoard Cylinder 14 18 8
Pin Up Cylinder 6 23 4
Clamp Cylinder
Pump Type Pressure Compensated Piston Pump
Pump Flow 75 gpm
Valve Type 3 or 5 Section
Filtration 3 Micron, Pressure Line
Hydraulic System Max Operating Pressure 3000 psig
Hydraulic Reservoir 90 gal 337.5 L

 

Dia (in)
Minimum 32
Maximum 42

Manufacturer Quincy QR-390, Stand Alone
Drive Type Deutz Engine
Pressure 210 psig
Flow 67.0 acfm @ 175 psig

Length 26′-0″ 7,925 mm
Width 9′-10″ 2,997 mm
Height 10′-3″ 3,124 mm
Weight (lbs/kg) 78,000 lbs 35,455 kg
Track Size 30 Ton

Manufacturer DP
Drive Type Hydraulic Motor
Pulling Force 20,000 lbf
Cable Diameter .5625″
Free Wheeling Drum

Cat C6.6 Diesel 173 hp
Operating Speed 2200 rpm
Fuel Tank 25 gal

  • Stand alone air compressor
  • Cold weather operating kit (-40º) available

NOMINAL PIPE O.D.MAXIMUM WALL THICKNESS BY GRADERECOMMENDED BEND
IN/MMX52X60X65X70X80X100DEGREE PER ARC FOOTRADIUS FEETMAXIMUM 40 FOOT JOINT
42 / 10662.9912.5722.3652.1881.9041.510.5011512.46
40 / 1016---2.4302.1121.6740.5011512.46
38 / 965----2.3581.8660.5011512.46
36 / 914-----2.0950.5011512.46
34 / 864------0.5011512.46
32 / 813------0.5011512.46

• A cell marked with a (-) represents the ability to bend up to 2.00″ thick. For wall thickness greater than that, contact DMI.
• Figures above represent empirical data and are recommendation only. They do not constitute a warranty.
• All bends are based on the use of DMI mandrels and approved Die Sets.
• For heavy wall pipe special Die Sets may be required.
• Figures shown above are provided as “Average” and will vary depending on the following:

  • Actual wall thickness of the pipe.
  • Actual Yield Stress of the pipe.
  • Skill of the Operators handling the Bending Machine and Mandrel.
  • Origin and Quality of the pipe.
  • Type of Die and Bending Set being used.

• Normal unbend tangent for PBM 6-20 is 5′
• Normal unbend tangent for PBM 16-30 is 6′
• Normal unbend tangent for PBM 22-36 is 6′
• Normal unbend tangent for PBM 32-42 is 7′
• Normal unbend tangent for PBM 48-60 is:

  • 11′ for Stiffback end with pipe support
  • 13′ for Stiffback end with NO pipe support
  • 8′ for Pinup end with pipe support
  • 9′ for Pinup end with NO pipe support

Disclaimer:
Technical information provided for this equipment regarding performance, specifications, dimension and weights can vary depending on final configuration of the equipment. Please contact DMI International for actual specifications at time of shipment.

DMI International does not accept responsibility for errors regarding the technical information, nor the consequences of any errors, nor the consequences to changes in the specifications contained herein. DMI International reserves the right to modify the equipment performance and specifications without notice.